Difference between revisions of "SRTM"

From PathlossWiki
Jump to: navigation, search
(Pathloss download tool)
 
(33 intermediate revisions by one user not shown)
Line 1: Line 1:
All SRTM data is available directly from '''http://dds.cr.usgs.gov/srtm/'''
+
==Information==
 +
There are 2 ways that SRTM data can be used with Pathloss 5. The data can be configured as a DEM and used for all profile and background generation or it can be used in conjunction with a bare earth DEM (such as [[NED data in GridFloat format]]) as a clutter database. The difference in elevation, when compared to a bare earth DEM is assigned to the clutter height. Both sets of instructions are given below.
  
Worldwide 1" SRTM data is available from '''http://e4ftl01.cr.usgs.gov/SRTM/SRTMGL1.003/2000.02.11/'''. The files you want to download have the extension '''.SRTMGL1.hgt.zip'''.  
+
SRTM data is collected by using a stereo radar scan of the earths surface. As a result the data tends to include the trees and buildings as these would be what reflects the radar signal. We say tends because there are variables, especially when dealing with trees. Depending on the tree type (deciduous or evergreen) and the time of year the data was collected, the heights could vary significantly. The radar signal also penetrates into the tree canopy to some degree. These variables need to be kept in mind when using SRTM as clutter. Additional caution needs to be exercised when using SRTM as a DEM, in particular the ground elevations at the antenna sites. It is always recommended to compare against elevations from a bare earth data source (if available), and use these for your site elevations. In North America the [[NED data in GridFloat format]] is excellent for this. It is not recommended to use clutter data when using SRTM as the DEM, as this would result in unrealistic clutter heights, almost doubling them in some cases.
  
 +
==How to download==
  
You can also use the download tool described below to download 1x1 degree blocks by coordinates.
+
The data can be downloaded using the [[FetchSRTM]] tool. This data is available for the world from latitude 60 degrees south to 60  degrees north.
  
==Information==
+
The files represent 1x1 degree blocks with naming representing the South Western corner of the block. The data files will have the extension '''.SRTMGL1.hgt.zip'''.  
There are 2 versions of the SRTM files. Information regarding the diferences can be found here: http://dds.cr.usgs.gov/srtm/What_are_these.pdf.  
+
  
'''Always use version 2 data if available.''' Version 2 has been cleaned up and most of the blanks, spikes and wells have been fixed.
 
  
==How to download==
+
== Using SRTM data as a DEM with the Pathloss 5 program. ==
  
====Pathloss SRTM download tool====
+
Click '''''Configure''''' - '''''Set GIS configuration'''''
[[Image:region_definition.jpg|400px|thumb|SRTM region definitions]]
+
Go to '''http://www.pathloss.net/fetchsrtm.exe'''
+
  
Select the download directory
 
Enter the bounding coordinates of the area of interest.''Be sure to uses negative longitudes in the western and southern hemispheres''. Select the desired product and click download. Data is downloaded in 1x1 degree blocks.
 
  
After downloading, unzip all the files in to a common folder.
+
[[File:GIS-SRTM.JPG]]
  
====Official SRTM Site====
 
The main SRTM download siteis found at: '''http://dds.cr.usgs.gov/srtm/'''
 
  
SRTM data are distributed in two levels:
+
Click the '''''Primary DEM''''' tab and select '''''SRTM (World)''''' from the '''''Digital elevation model''''' drop down list.
  
SRTM1 is 1-arc second data available for the USA only. The SRTM1 files are arranged by Regions as shown in the following graphic to the right.
+
Click the '''''File index''''' button and a new window will appear. In the menu of the new window click '''''Files''''' ,'''''Import index''''' and '''''SRTM hgt files'''''.
  
SRTM3 sampled at three arc-seconds available for the world. The SRTM3 files are arranged by continent. You may have to look in the neighboring continent to find the files you need (for example the Middle East is in Africa)
 
  
Data are divided into one by one degree latitude and longitude tiles in geographic projection.
+
[[File:SRTM-index.JPG]]
File names refer to the latitude and longitude of the lower left corner of the tile - e.g. N37W105 has its lower left corner at 37 degrees north latitude and 105 degrees west longitude.
+
  
After downloading, unzip all the files in to a common folder.
 
  
== How to use the SRTM data with the Pathloss 5 program. ==
+
Browse to locate the '''''HGT''''' files you have downloaded (You can select many HGT files at once by holding Ctrl or Shift while selecting files). Click '''''Open''''' and the files will be added to the index list.
 +
 
 +
Note the edges of the SRTM file(s) and ensure that they cover the area of your project. In other words, make sure that the sites coordinates fall within the rectangle bounded by the North, South, East and West edges as listed for the SRTM file(s) in the index.
 +
 
 +
You have now configured Pathloss 5 for SRTM terrain data.
 +
 
 +
== Using SRTM data as Clutter with the Pathloss 5 program. ==
 +
 
 +
When used with a bare earth DEM like [[NED data in GridFloat format]]. The Pathloss 5 program can be configured to take the difference between the elevations for a given point and assign this difference to the clutter height for that point. This feature is only used in profile generation and can not be used when viewing a background in the network view.
 +
 
  
 
Click '''''Configure''''' - '''''Set GIS configuration'''''
 
Click '''''Configure''''' - '''''Set GIS configuration'''''
  
[[File:GIS-SRTM.JPG]]
 
  
Click the '''''Primary DEM''''' tab and select '''''SRTM (World)''''' from the '''''Digital elevation model''''' drop down list.
+
[[File:GIS-SRTM-clutter.jpg]]
  
Click the '''''File index''''' button and a new window will appear. In the menu of the new window click '''''Files''''' ,'''''Import index''''' and '''''SRTM hgt files'''''.
 
  
[[File:SRTM-index.JPG]]
+
Click '''''Clutter 2''''' tab and select '''''BIL geographic clutter''''' from the '''''Clutter model''''' drop down list.
  
Browse to locate the '''''HGT''''' files you have downloaded (You can select many HGT files at once by holding Ctrl or Shift while selecting files). Click '''''Open''''' and the files will be added to the index list.
+
Click the '''''Setup''''' button.
  
Note the edges of the SRTM file(s) and ensure that they cover the area of your project. In other words, make sure that the sites coordinates fall within the rectangle bounded by the North, South, East and West edges as listed for the SRTM file(s) in the index.
 
  
You have now configured Pathloss 5 for SRTM terrain data.
+
[[File:GIS-SRTM-clutter-setup.jpg]]
 +
 
 +
 
 +
Select the last option from '''''Clutter database format''''' and click the '''''OK''''' button.
 +
 
 +
 
 +
'''''DIGRESSION:'''''
 +
 
 +
 
 +
[[File:GIS-SRTM-clutter-setup3.jpg]]
 +
 
 +
 
 +
Notice the the '''''Definition''''' button has disappeared. This is because the SRTM data can only provide heights not the classification of the clutter ie. trees, building etc. Pathloss 5 will use the '''''Default clutter category''''' and the '''''Tree foliage''''' setting to define the clutter. These options are set in the '''''Default calculation options''''' and the '''''Calculation options''''' in Pathloss 5 and Pathloss 5 Link respectively. 
 +
 
 +
 
 +
[[File:GIS-SRTM-clutter-default.jpg]]
 +
 
 +
 
 +
'''''End DIGRESSION''''' and back to the setup...
 +
 
 +
 
 +
[[File:GIS-SRTM-clutter-setup2.jpg]]
 +
 
 +
 
 +
Click the '''''File index button'''''
 +
 
 +
 
 +
[[File:GIS-SRTM-clutter-index.jpg]]
 +
 
 +
 
 +
Click '''''Files - Import index - SRTM hgt files'''''
 +
 
 +
 
 +
[[File:GIS-SRTM-clutter-index2.jpg]]
 +
 
 +
 
 +
You can multi select file by holding '''''Ctrl''''' or '''''Shift''''' while selecting files. Click '''''Open''''' and the selected files will be indexed. Pathloss 5 is now configured to use SRTM as clutter. Make sure that the correct Clutter source is selected when generating profiles. These option are shown when generating profiles in the '''''Terrain data''''' section under '''''Configure - Generate profile''''' and also in the '''''Link design rules''''' when creating point to point and point to multi point links.
  
 
== How to use the SRTM data with the Pathloss 4 program. ==
 
== How to use the SRTM data with the Pathloss 4 program. ==
Line 60: Line 93:
 
The SRTM data uses the WGS84 datum. Your coordinates will be transformed automatically.
 
The SRTM data uses the WGS84 datum. Your coordinates will be transformed automatically.
  
In the Pathloss program click "Configure" "Terrain Database" and select "SRTM" from the drop down list. Click Setup Primary (or Secondary depending on your selection). Click "File" then "BIL-HDR-BLW" and browse to find and load a file with the HGT extension. The program is now setup to use the selected SRTM file.
+
In the Pathloss program click '''''Configure – Terrain Database''''' and select '''''SRTM''''' from the drop down list. Click '''''Setup Primary''''' (or '''''Secondary''''' depending on your selection). Click '''''File''''' then '''''BIL-HDR-BLW''''' and browse to find and load a file with the HGT extension. The program is now setup to use the selected SRTM file.

Latest revision as of 13:19, 11 October 2022

Contents

Information

There are 2 ways that SRTM data can be used with Pathloss 5. The data can be configured as a DEM and used for all profile and background generation or it can be used in conjunction with a bare earth DEM (such as NED data in GridFloat format) as a clutter database. The difference in elevation, when compared to a bare earth DEM is assigned to the clutter height. Both sets of instructions are given below.

SRTM data is collected by using a stereo radar scan of the earths surface. As a result the data tends to include the trees and buildings as these would be what reflects the radar signal. We say tends because there are variables, especially when dealing with trees. Depending on the tree type (deciduous or evergreen) and the time of year the data was collected, the heights could vary significantly. The radar signal also penetrates into the tree canopy to some degree. These variables need to be kept in mind when using SRTM as clutter. Additional caution needs to be exercised when using SRTM as a DEM, in particular the ground elevations at the antenna sites. It is always recommended to compare against elevations from a bare earth data source (if available), and use these for your site elevations. In North America the NED data in GridFloat format is excellent for this. It is not recommended to use clutter data when using SRTM as the DEM, as this would result in unrealistic clutter heights, almost doubling them in some cases.

How to download

The data can be downloaded using the FetchSRTM tool. This data is available for the world from latitude 60 degrees south to 60 degrees north.

The files represent 1x1 degree blocks with naming representing the South Western corner of the block. The data files will have the extension .SRTMGL1.hgt.zip.


Using SRTM data as a DEM with the Pathloss 5 program.

Click Configure - Set GIS configuration


GIS-SRTM.JPG


Click the Primary DEM tab and select SRTM (World) from the Digital elevation model drop down list.

Click the File index button and a new window will appear. In the menu of the new window click Files ,Import index and SRTM hgt files.


SRTM-index.JPG


Browse to locate the HGT files you have downloaded (You can select many HGT files at once by holding Ctrl or Shift while selecting files). Click Open and the files will be added to the index list.

Note the edges of the SRTM file(s) and ensure that they cover the area of your project. In other words, make sure that the sites coordinates fall within the rectangle bounded by the North, South, East and West edges as listed for the SRTM file(s) in the index.

You have now configured Pathloss 5 for SRTM terrain data.

Using SRTM data as Clutter with the Pathloss 5 program.

When used with a bare earth DEM like NED data in GridFloat format. The Pathloss 5 program can be configured to take the difference between the elevations for a given point and assign this difference to the clutter height for that point. This feature is only used in profile generation and can not be used when viewing a background in the network view.


Click Configure - Set GIS configuration


GIS-SRTM-clutter.jpg


Click Clutter 2 tab and select BIL geographic clutter from the Clutter model drop down list.

Click the Setup button.


GIS-SRTM-clutter-setup.jpg


Select the last option from Clutter database format and click the OK button.


DIGRESSION:


GIS-SRTM-clutter-setup3.jpg


Notice the the Definition button has disappeared. This is because the SRTM data can only provide heights not the classification of the clutter ie. trees, building etc. Pathloss 5 will use the Default clutter category and the Tree foliage setting to define the clutter. These options are set in the Default calculation options and the Calculation options in Pathloss 5 and Pathloss 5 Link respectively.


GIS-SRTM-clutter-default.jpg


End DIGRESSION and back to the setup...


GIS-SRTM-clutter-setup2.jpg


Click the File index button


GIS-SRTM-clutter-index.jpg


Click Files - Import index - SRTM hgt files


GIS-SRTM-clutter-index2.jpg


You can multi select file by holding Ctrl or Shift while selecting files. Click Open and the selected files will be indexed. Pathloss 5 is now configured to use SRTM as clutter. Make sure that the correct Clutter source is selected when generating profiles. These option are shown when generating profiles in the Terrain data section under Configure - Generate profile and also in the Link design rules when creating point to point and point to multi point links.

How to use the SRTM data with the Pathloss 4 program.

You will need the latest version of the Pathloss program.

The SRTM data uses the WGS84 datum. Your coordinates will be transformed automatically.

In the Pathloss program click Configure – Terrain Database and select SRTM from the drop down list. Click Setup Primary (or Secondary depending on your selection). Click File then BIL-HDR-BLW and browse to find and load a file with the HGT extension. The program is now setup to use the selected SRTM file.